How to Repair a Burst Pipe

Fix it and prevent it from freezing again with these instructions.
Water Line Pressure Gauge

Water Line Pressure Gauge

You don't need advanced plumbing skills to fix a burst pipe -- just some soldering equipment. And by adding a stop and waste valve, you'll be going a long way toward ensuring that the pipe doesn't freeze again.

You don't need advanced plumbing skills to fix a burst pipe -- just some soldering equipment. And by adding a stop and waste valve, you'll be going a long way toward  ensuring that the pipe doesn't freeze again. Here's what to do:

Materials and Tools:

mini copper-pipe cutter

steel wool

lead-free solder

soldering paste

torch kit (torch and striker)

good ½-inch copper pipe

stop and waste valve

½-inch copper fittings

Steps:

  1. Determine a location for the valve on a water line in or near a heated area.
  2. Shut off the main valve where water comes into your home. Open the lowest fixture in your house to drain any water out.
  3. Use a pipe cutter to remove the desired section of pipe. Rotate the pipe cutter around the pipe, gradually tightening it until it cuts through. Clean any burrs off the end of the cut pipe with steel wool. Place a bucket under the cut area to catch any water remaining in the line.
  4. Temporarily remove the petcock (small screw) from the valve. Be sure to install the valve in the right direction. An arrow points in the direction of the water flow.
  5. Cut a section of copper pipe to the appropriate length. Allow a little extra length for a good fit. Be sure the new pipe is of the same diameter as the existing water line (usually ½-inch).
  6. Use steel wool to clean both the pipe end and inside the stop-and-waste valve.
  7. Spread soldering flux on the outside of the pipe end and inside the valve fitting.
  8. Slide the valve fitting onto the end of the pipe.
  9. Wearing safety goggles, use a propane torch to heat the fitting and the pipe where they connect. For best results, hold the edge of the blue flame right against the pipe.
  10. Push about 2 inches of solder into the joint where the valve connects to the pipe. The heat will melt the solder and allow it to seep into the connection. Solder completely around the pipe-valve connection. Practice the soldering technique on scrap pieces of pipe and copper fittings before trying it on the valve.
  11. Use the same soldering techniques to install the new assembly to the water line. Depending on the installation, it may be necessary to use some inexpensive copper fittings to connect new sections of pipe to the existing water line. These copper fittings are widely available in different configurations and diameters.
  12. Replace the petcock, and open the main water line to check for leaks. Before temperatures dip below freezing, shut off the valve and open any spigots that are downstream of the valve. Then remove the petcock screw to drain the pipe. If any sections of pipe upstream of the new valve are in an unheated area, cover them with foam pipe insulation.
Keep Reading

Next Up

Which Home Improvements Pay Off?

Basic maintenance, such as the roof and exterior painting, are frequently more important than an awesome kitchen.

How to Repair Lawn Edges

If not repaired, damaged edges will continue to deteriorate, and like any bare patch, they also provide an open invitation for weeds to establish. Reseeding a damaged edge is rarely effective, so try tackling the problem using this simple technique.

How to Repair Bald Spots in Your Lawn

Find out how to get bald spots in your lawn to start sprouting.

Fall Lawn Care: How to Repair After a Drought

Summer can leave lawns hard and patchy. Try these tips for improving a summer-damaged lawn. 

How to Repair Crown Molding

Cut a replacement piece to match and no one's the wiser.

How to Plant Evergreens in Containers

Learn how to properly plant evergreens in containers to keep color alive in your garden all year around.

How to Organize a Bathroom

Professional organizer Linda Koopersmith walks through bathroom organization, from the countertops to the shower. Follow these 6 simple tips for a clutter-free bathroom.

How to Paint the Exterior of a House

HGTV.com walks you through the steps of painting the exterior of a house, from prep work through the finishing touches.

How to Clean Carpet Stains

A good quality carpet could last for many years with proper care and maintenance.

How to Install Wall-to-Wall Carpeting

The experts show how to install wall-to-wall carpeting.

On TV

House Hunters

7:30am | 6:30c

House Hunters

8:30am | 7:30c

House Hunters

9:30am | 8:30c

House Hunters

10am | 9c

House Hunters

10:30am | 9:30c

House Hunters

11am | 10c

House Hunters

11:30am | 10:30c

Fixer Upper

12pm | 11c

Fixer Upper

1pm | 12c

Fixer Upper

2pm | 1c

Fixer Upper

3pm | 2c

Fixer Upper

4pm | 3c

Fixer Upper

5pm | 4c

Fixer Upper

6pm | 5c

Fixer Upper

7pm | 6c
On Tonight
On Tonight

Fixer Upper

8pm | 7c

Fixer Upper

9pm | 8c

House Hunters

10pm | 9c

Montana Home

11pm | 10c

Fixer Upper

12am | 11c

House Hunters

1am | 12c

Fixer Upper

3am | 2c

Shop This Look

Found a living space you love in HGTV's Photo Library? Get the look in your own home with products from Wayfair.

Follow Us Everywhere

Join the party! Don't miss HGTV in your favorite social media feeds.