Step Up Your Garage Game With a DIY Staircase

Improve the look and safety of your garage with these simple, DIY steps.

How to Build a Garage Staircase
Loading Video...

If you’re like most people, your homebuilder decided to spend the very least amount of time on your garage. Unfinished walls, questionable drywall work and, of course, the classically wonky concrete steps. Not only are they an eyesore, they aren’t always safe either. Take matters into your own hands and cover them up with a beautiful set of wooden stairs.

Materials Needed

  • 4x8 sheet of 1/2” plywood
  • (3) 2x4 x 6’ pine boards
  • (2) 1x4 x 6’ pine boards
  • 11-1/4” stair tread
  • 1” wood screws
  • 2-1/4” wood screws
  • wood stain
  • paint rags
  • clear polyurethane
  • L-square
  • pencil
  • table saw
  • safety glasses
  • drill + bits
  • white interior paint
  • paint brush
  • waterproof flashing roll
  • brad nail gun
  • wood glue
  • painter’s putty
  • 120-grit sanding block
  • pry bar

Measure for New Stairs

Before buying wood, measure your stairs to figure out what you need. The wood measurements we used are based on our specific set of steps and may need to be slightly adjusted to suit your needs. Once you’ve measured, adjust the list accordingly.

Pro Tip: When possible, have large items such as plywood sheets cut into smaller pieces by the hardware store. This makes the trip home and unloading much easier and will also save you some time.

Prep the Stair Space

Begin by using a pry bar to remove any existing trim around the old steps. Secure one 36-inch 2x4 an inch under the threshold. This will be what you later screw the new stair base to. Leaving an inch of space allows room for the stair tread.

Cut Out the Base

To fit our space, we traced out a large rectangle measuring 13.5 inches by 29.5 inches. Then, we marked the three stairs measuring four inches tall and ten inches deep. Based off of the measurements of your staircase, use your L-square to measure the outline of the base on the plywood. Wearing safety glasses, cut out the pattern using a table saw. When finished, trace the shape on another piece of plywood and repeat this process once more.

Assemble the Base

Use 1-inch wood screws to attach the plywood pieces to a 36-inch 2x4 at the front of each step. Cut out narrow strips of flashing to put on the bottom of the stair base for a waterproof barrier. Paint the base with two coats of white paint.

Secure in Place

Slide the base in place around the 2x4 that is attached below the door and secure with wood screws. Add a 2x4 tread support on top of each step (two total). Attach these supports to the stringers using wood screws.

Attach Stair Tread and Complete

Cut all three stair treads down to 39 inches long (based on your measurements, just make sure there is a one-inch overhang on all three sides of the tread). Sand and stain. Once dry, apply a coat of polyurethane following the manufacturer’s instructions. Run a bead of wood glue on top of each stair base and place the treads on each step, using a nail gun to secure in place. Finish off by using the nail gun to attach painted 37-inch 1x4’s to the front of each riser. To complete, fill screw holes and nail holes with painter’s putty, sand and touch up with paint.

Photo by: Shain Rievley

Shain Rievley

5 Easy Steps to DIY Farmhouse-Style Trim

The clean, fresh and oh-so-beautiful farmhouse trim you’ve been dreaming of is just a few steps away.

Next Up

How to Build an Outdoor Wood and Gravel Staircase

Use pea gravel and wood posts to build steps in your yard.

How to Paint a Staircase

Learn how to paint a decorative runner on a wooden staircase.

How to Create a Resin Bar Tray

Take your bar or coffee table up a notch with this art-deco-inspired tray you can DIY in a matter of minutes.

How to Make a Plinko-Style Bottle Opener Game

Liven up your next party with this Plinko-inspired game where falling bottle caps decide the outcome.

DIY Two-Tiered Garage Storage Stand With Ramp

Double your garage or shed storage space with this two-tiered stand ideal for wheelbarrows and utility carts.

How to Make an Upholstered Headboard

HGTV Magazine helped decorate one of the bedrooms in the 2016 DIY Network Blog Cabin. Here's how to recreate the headboard in your own home.

Make These DIY Specimen Jars to Liven Up Your Creepy Halloween Decor

Be your own Frankenstein and create this spine-tingling decor with water, calcium chloride, sodium-alginate powder and food coloring.

How to Build a Raised Garden Bed Step-by-Step

Take your garden to the next level with this complete plan and step-by-step instructions for an easy raised garden bed DIY project. Your plants (and wallet) will thank you.

Upgrade Your Laundry Room With This DIY Fold-Down Drying Rack

Make laundry day a little easier with this space-saving clothes drying rack. It drops down when you need it, and folds away when you don’t. With adjustable levels, you can determine how far you want to extend it.

Go Shopping

Get product recommendations from HGTV editors, plus can’t-miss sales and deals.

On TV

Home Town

12pm | 11c

Home Town

1pm | 12c

Home Town

2pm | 1c

Home Town

3pm | 2c

Home Town

4pm | 3c

Home Town

5pm | 4c

Home Town

6pm | 5c
On Tonight
On Tonight

Bargain Block

9pm | 8c

House Hunters

10pm | 9c

House Hunters

10:31pm | 9:31c

House Hunters

11pm | 10c

House Hunters

11:30pm | 10:30c

Bargain Block

12am | 11c

House Hunters

1am | 12c

House Hunters

1:31am | 12:31c

House Hunters

2:30am | 1:30c

Follow Us Everywhere

Join the party! Don't miss HGTV in your favorite social media feeds.