How to Install a Whole-House Fan

Learn how to keep your cool by installing a whole-house fan.

When the air inside your house is too warm but the outside air is comfortable, you can use a whole-house fan to bring some of that cooler air into your living space. The fan is installed in the ceiling just below your attic, and it’s hidden by louvers so that it won’t look out of place. Here’s how to install one yourself:

Whole-house fans are typically controlled by thermostats, wall switches or pull cords. They can usually be wired to work in conjunction with a power ventilator on the roof.

Before you set out to buy your fan, make sure you know the square footage of your home. This will help you determine the correct fan to use.

Here’s how to install a whole-house fan:

Materials and Tools:

whole-house fan
drill, with drill bits and driver bits
wrenches
hammer
framing nails
2-by-4-inch studs
drywall saw
handsaw
measuring tape
framing square
wire stripper
wire nuts
safety glasses
work gloves
long-sleeve shirt
dust mask

Steps:

1. Remove the blades from the whole-house fan before you begin installing it. This reduces the weight and makes the fan less cumbersome.

2. On the uppermost ceiling in the living area of your home, locate a central point where the ceiling is directly below the attic. Measure the area to be sure your fan will fit.

3. From the attic, go to the general location where you plan to install the fan. Make sure the area is free of obstructions such as ductwork and plumbing. Move the insulation, electrical wiring, and other obstacles away from the area. (Be sure to wear long sleeves, work gloves, and a dust mask if you'll be working with fiberglass insulation.)

4. Measure the installation space from inside the attic. If your fan will span two ceiling joists, make reference marks on either side of the center joist and drill holes through the ceiling so you can make your final cuts from below.

5. From the floor below, use the hole(s) you just drilled as a reference to measure and mark cutting lines on the ceiling. The lines should be based on the inside dimensions of the louver flange. Double-check the lines to make sure they’re square, and cut them with a drywall saw or a reciprocating saw. Be careful not to damage the rest of the ceiling. You may need an assistant to help you hold the ceiling material in place so that it doesn’t fall prematurely.

6. Remove fasteners such as drywall nails or screws from any exposed joists.

7. Create a frame to support the fan using 2-by-4-inch blocking between the joists around the cut area of the ceiling. This will serve the dual purpose of supporting the weight of the fan and providing support for the ceiling material.

8. Install brackets in the pre-drilled holes in the frame of your fan. Fasten the brackets tightly.

9. Set the fan in place and mark the bracket holes. Remove the fan and drill pilot holes. Then set the fan back in place and secure it with bolts.

10. When the fan is secure, reattach the fan blades. Spin the fan to make sure the blades turn freely.

11. Make the electrical connections for the fan based on the manufacturer's instructions. You may wish to hire a licensed electrician to make these connections.

12. Secure the louver to the ceiling.

Next Up

How to Install French Drains

Divert groundwater from the basement or foundation with the help of gravel and fabric.

How to Replace a Faucet

Replacing a faucet that's outdated or always dripping is a relatively easy DIY project.

How to Replace a Window

When it's time to replace an outdated, inefficient window, it can be hard to know where to start, so we’ve got everything you need to know to get the job done.

How to Install Wainscoting to a Wall

Add an instant touch of class to a room with these step-by-step instructions on installing beadboard wainscoting.

How to Wire a Light Switch

Electricity is a mystery to many people, but some electrical projects — like wiring a switch — are so simple that anyone can do them. With a few easy steps and the right knowledge, there’s no need to hire an electrician.

How to Clean a Humidifier

Improve your home's air quality by disinfecting one of the most important small appliances you’re probably forgetting to clean.

How to Remove a Stripped Screw

Keep all your projects moving and say goodbye to stripped screws once and for all with these helpful tips and tricks.

How to Clean a Computer Screen

Get the low-down on how to safely remove dust, fingerprints, smudges and streaks from any type of laptop screen or computer monitor.

How to Drain a Water Heater

Extend your water heater's life span by draining the tank annually to remove any sediment that may have built up.

8 Ways to Fix Drafty Windows

Save money and stay warm this winter with these DIY ways to insulate and weather-strip windows as well as doors.

Go Shopping

Get product recommendations from HGTV editors, plus can’t-miss sales and deals.

On TV

Follow Us Everywhere

Join the party! Don't miss HGTV in your favorite social media feeds.