How to Install Gutters

Protect against water damage to your foundation, basement and driveway with these instructions.
Related To:
Painted Aluminum Gutter Against Stucco Wall

Painted Aluminum Gutter Against Stucco Wall

Protect against water damage to your foundation, basement and driveway with these instructions to properly install your gutters.

Moisture can be a devastating enemy to your home, but a properly installed and maintained gutter system will protect it from water damage.

As for the maintenance, clear gutters of debris at least twice a year-spring and fall are good choices. Remove leaves, straw and other debris by hand, and then rinse through with a garden hose; trying to rinse debris down the gutters can clog the downspouts. A screening system can save you a lot of time by keeping debris out of the gutters in the first place.

As for the installation, here's how (you'll need an extra set of hands): 

Materials and Tools:

tape measure

two ladders

graph paper

gutter sections

downspouts

gutter hardware

mason's line

chalk line

gutter-seam sealant

power drill

gutter splash guards

hidden fasteners

tin snips

safety gloves

Steps:

  1. To determine how much material you'll need, add the lengths of each fascia along the roofline, taking the measurements from the outer edges of the shingles. Mark the measurements and make an outline on graph paper. Mark the locations of the downspouts with an "X" -- plan on one downspout per gutter per 20-foot run. Finally, measure and add the heights from the ground to the roofline in the locations where the downspouts will go. Note: You need to have enough gutter to catch the watershed. For about every 20 feet of gutter, you need at least a ½-inch of drop. This will ensure that the water ends up in the downspouts.
  2. If you're replacing an existing gutter system, once the old system is removed check for rot along the fascia board. If there's damage, you can place a fascia plate or fascia cover over it or just replace the fascia board.
  3. Drive a nail into the fascia at one end of the gutter-run wall ½-inch below the top of the fascia. Stretch a mason's line from the nail. To properly align the slope (using a line level on the mason's line), drop one end of the line a ¼-inch for each 25 feet of fascia length; mark that point with a pencil. Snap a chalk line from the marks to show where the top of the gutter will be attached. Note: Pitch longer runs toward an outlet at either end, as opposed to just one end. The gutters should always be pitched away from the front valleys and toward the corners.
  4. Lay gutters on the ground as a model for how they will go on the fascia. Wearing gloves, use tin snips to cut the gutters to length. Smooth the sharp aluminum edges with a file. Apply gutter-seam sealant to the gutter section that requires an end cap, to prevent leaking.
  5. Working from the end of the fascia, use hidden fasteners to attach the end-cap gutter. Slip hidden fasteners into the gutter run, and screw the gutter into the fascia with a drill and screws.
  6. Using the chalk line to keep the gutters flush with the slope line, attach the downspout outlet to the fascia with the power drill. Continue this process with gutter sections. Hidden fasteners are placed every 24 inches along the gutter run. When two pieces of gutter come together, use a gutter connector on the exterior seam and gutter sealant on the interior to prevent leaks.
  7. To attach a downspout, assemble an elbow and a short length of downspout to carry the run to the wall. Anchor the downspout to the wall with two brackets, one near the top of the wall and the other just above the foundation. Attach another elbow at the bottom of the downspout to divert water away from the foundation. Place a splash guard under it to keep water from eroding the soil.
Keep Reading

Next Up

How to Install Wall-to-Wall Carpeting

The experts show how to install wall-to-wall carpeting.

How to Install French Drains

Divert groundwater from the basement or foundation with the help of gravel and fabric.

How To: Installing a Fire Pit

A backyard gets more warm and hospitable with a stone firepit.

How to Install Beadboard Wainscoting

Beadboard wainscoting gives a family room a cozy lake-side feel.

How to Install Crown Molding

Install crown molding to add visual interest and value to your home.

How to Install Tile in a Bathroom Shower

Use these step-by-step instructions to take your shower from drab to fab by installing Italian marble tile.

How to Install a Shower Tile Wall

Update your bathroom by installing tile in the shower.

How to Install a Planked Wood Ceiling

Add architectural detail and rustic, farmhouse charm to a builder basic bedroom with a tongue-and-groove planked wood ceiling. This is also a great way to cover up dated, cottage cheese ceilings or a sloppy drywall job.

How to Install Snap-Together Laminate Flooring

Installing snap-together flooring allows anyone with moderate DIY skills to create a beautiful new laminate floor.

How to Install a Marble Tile Backsplash

Boost your kitchen's wow factor in a three-day weekend by installing a timeless Carrara marble backsplash in an updated subway tile pattern.

On TV

Rehab Addict

6:30am | 5:30c

Rehab Addict

7:30am | 6:30c

House Hunters

1pm | 12c

House Hunters

1:30pm | 12:30c

House Hunters

2:30pm | 1:30c

House Hunters

3:30pm | 2:30c

House Hunters

4:30pm | 3:30c

House Hunters

5:30pm | 4:30c

House Hunters

6:30pm | 5:30c

House Hunters

7:30pm | 6:30c
On Tonight
On Tonight

Tiny House Hunters

8pm | 7c

Tiny House Hunters

8:30pm | 7:30c

House Hunters

9:30pm | 8:30c

House Hunters

10pm | 9c

House Hunters

11pm | 10c

House Hunters

12am | 11c

House Hunters

12:30am | 11:30c

House Hunters

1am | 12c

Tiny House Hunters

3:30am | 2:30c

Shop This Look

Found a living space you love in HGTV's Photo Library? Get the look in your own home with products from Wayfair.

Follow Us Everywhere

Join the party! Don't miss HGTV in your favorite social media feeds.