How to Install Wall-to-Wall Carpet Yourself

Installing new carpet not only enhances the beauty of a room but provides insulation, sound control, and a comfortable surface to walk on.

Related To:

DIR141_3fq-stretching-carpet_s4x3

Materials and Tools:

carpet
tackless strip
tape
power stretcher
gloves
tack strip cutter
razor knife
measuring tape
knee kicker
stair tool
hand stapler
hammer
carpet knife
top cutter
wall trimmer

Steps:

1. Measure the longest walls in your room. Multiply the length and width, and divide by 9 to determine the square yardage. Add 10 percent to allow for errors, irregularities and pattern matching.

2. Make sure the surface to be carpeted is smooth and clean. Scrape up any paint or joint compound and sweep and vacuum the floor thoroughly.

3. If possible, remove the doors from the room so you won't have to work around them. Having the doors out of the way will also make it easier for you to cut off the bottoms of the doorjambs if necessary.

DIR141_3fc-laying-tack-strip-on-edges_s4x3

4. Cut the tackless strips to size with a strip cutter or heavy snips. Nail the strips 1/2" from the wall. Don't install tackless strips across thresholds or doorways; the tacks on the strips are sharp and could poke through the carpet and hurt your feet. Tackless strips come in a variety of widths, thicknesses and heights. Make sure you're using the correct size. If you're installing carpet over a concrete subfloor, use masonry tacks or epoxy adhesive to hold the tackless strips in place.

DIR141_3ff-attaching-pad-to-floor_s4x3

5. Lay out the carpet pad perpendicular to the direction you plan to install the carpet, and staple it near the tackless strips with a staple hammer.

6. Staple the seam of the pad, alternating staples so that they aren't beside one another. Stretch the padding so that the pieces are butted tightly together.

DIR141_3fh-cutting-removing-padding_s4x3

7. Feel through the padding to locate the tackless strip, and use a utility knife to cut away the padding along the interior edge of the strip so that all the tacks are exposed.

8. Measure the room at its longest point, and add 3" to the measurement. Take the carpet outside if possible, and notch the back on both sides at the appropriate length. The carpet will be easier to handle outside. You might want someone to help you.

DIR141_3fj-roller-carpet-on-concrete_s4x3

9. Roll the carpet with the back facing outward until the notched areas show. Then run a chalk line from notch to notch. Cut the back of the carpet along the chalk line, roll up the carpet, and take it back inside.

DIR141_3fk-cutting-carpet_s4x3

10. Roll out the carpet into the room. Keep it as straight as possible. Cut away excess carpet, but leave about 3" extra next to the walls. Lay out any additional carpet needed to fill the room.

DIR141_3fm-carpet-installation_s4x3

11. Where the carpet edges join, you'll need to create a seam. The seamed edges of both carpet segments must be straight. Check the edges: don't assume that a factory edge is straight. Place a piece of seaming tape under the seam, adhesive side up. Heat the seaming iron to the temperature recommended by the tape manufacturer, and rest it directly on the tape for 15 to 30 seconds. Then slowly slide the iron along the tape, and press the seam into the melted glue behind the iron. After the pieces are joined, place heavy objects on the seam to hold it in place as the glue dries. Seams should run parallel to the room's main light source. And make sure the pile of both pieces leans in the same direction.

12. Dry-fit the carpet, butting one end against a wall. Use a carpet knife to trim the carpet to fit around obstacles.

13. Attach the carpet to the tackless strips at one end of the room, using the knee kicker. Place the face of the knee kicker against the carpet about 3" away from the wall, and forcefully strike the padded end to stretch the carpet over the tackless strips.

DIR141_3fp-carpet-installation_s4x3

14. Trim excess carpet with a wall trimmer, which rests against the wall and provides a straight cut at the correct spot. Use a stair tool to press the cut edges underneath the baseboard trim.

15. Use the power stretcher to attach to the strips on the other side of the room. For corners and alcoves where the power stretcher can't reach, use the knee kicker and stair tool.

DIR141_carpet-binder-bar-wood-block_s4x3

16. Nail a binder bar to any areas where the carpet ends without abutting a wall such as a threshold. Stretch the carpet with the knee kicker to link to the hooks in the binder bar then use a wooden block or scrap piece of lumber to close the binder bar onto the edge of the carpet.

17. When all the carpet is in place, cut out the vent openings. Attach shoe molding around the room if desired.

Tip: At the point where the carpet extends into the alcove, fold it at the depth of the alcove before you beginning to roll it up. Then roll toward the folded section. When unrolling the carpet, start at the end of the room closest to the alcove.

Next Up

How to Install Carpet Tiles

Installing carpet squares, or carpet tiles, is not only easy but it is a simple way to add bold colors and patterns to a room. Best of all, the colors and patterns are easily customized to fit the decor of any home.

How to Install a Carpet Runner on Stairs

A runner can add a splash of color to any room and make stairs more comfortable to walk on.

How to Repair Carpet

Learn how to fix damaged carpet with these step-by-step instructions so the repair blends in seamlessly.

How to Remove Wall-to-Wall Carpet

Removing old yucky carpeting can be one of the most satisfying DIY jobs. Plus, doing it yourself will save money. You’ll need just a few basic tools and less than half a day to complete the job.

2024: Average Cost to Install Carpet Per Square Foot

Knowing the average cost of installing carpet can help you dial in your remodeling budget.

How to Install Wainscoting to a Wall

Add an instant touch of class to a room with these step-by-step instructions on installing beadboard wainscoting.

How to Remove Pet Stains From Carpet

Urine or vomit on carpet can be a pet owner's worst nightmare. Here's how you can clean some of the most common pet messes without too much stress.

How to Get Stains Out of Carpet

A good quality carpet could last for many years with proper care and maintenance. Learn how to remove stains from wine, nail polish, coffee and more.

How to Remove Coffee Stains From Carpet

With just a few household items and our simple tips and tricks, that daunting coffee stain will be no more.

How to Remove an Ink Stain From a Rug or Carpet

Removing an ink stain isn't such an easy task because of its chemical properties. But with a little patience and persistence, the stain will be gone before your eyes.

Go Shopping

Get product recommendations from HGTV editors, plus can’t-miss sales and deals.

On TV

Follow Us Everywhere

Join the party! Don't miss HGTV in your favorite social media feeds.